EasyTechnology.gr - Consumer electronics, Technology is easy with us!

Supports AVR Studio 4 ONLY. Doesn't support AVR Studio 5/6 or higher versions. AVR ISP Programmer, compatible with AT AVRISP from ATMEL A professional low cost In-System Programmer. Programs FLASH , EEPROM, Fuses, and Lock Bit through USB Features Programs all AVR Devices with ISP programming option, and certain 51 Devices Programs both Flash and EEPROM Supports Fuses and Lock Bit Programming Based on STK500 firmware upgradable to Support Future Devices Adjustable Speed. Supports high speed programming up to 926K frequency Quasi-USB interface to PC for Programming and Control (using PL2303TA, USB To RS232) 3 optional cables to target board Powered from USB bus. No need for Additional Power Supply Based on AT AVRISP - Compatible with AT AVRISP, easy to use, stable and reliable Based on STK500 firmware - Identified as AVRISP/STK500 in AVRStudio, high speed programming AVR Studio 4 firmware - Supports AVR Studio 4 - NOT upgradable Supported software - AVR Studio or WINAVR(GCC) is used as front-end software - Supports the program files generated by IAR, ICCAVR, CVAVR Device Support - USB AVRISP supports all AVR 8-bit RISC Micro Controllers with ISP programming option. Support for new devices will be added through new versions of AVR Studio. - Supports AT86RF401/AT89S51/AT89S52 Refer to AVRStudio 4.18, the following devices are supported: Classic Tiny* Mega* Other AT90S1200 AT90S2313 AT90S/LS2323 AT90S/LS2343 AT90S/LS2333 AT90S4414 AT90S/LS4433 AT90S/LS4434 AT90S8515 AT90S/LS8535 ATtiny12 ATtiny13 ATtiny15 ATtiny22 ATtiny2313 ATtiny24 ATtiny25 ATtiny26 ATtiny44 ATtiny45 ATtiny461 ATtiny84 ATtiny85 ATtiny861 ATmega48 ATmega48P ATmega8 ATmega88 ATmega88P ATmega8515 ATmega8535 ATmega16 ATmega162 ATmeg164P ATmega165 ATmega165P ATmega168 ATmega168P ATmega169 ATmega169P ATmega32 ATmega324 ATmega324P ATmega325 ATmega325P ATmega3250 ATmega3250P ATmega329 ATmega329P ATmega3290 ATmega3290P ATmega64 ATmega640 ATmega644P ATmega645 ATmega6450 ATmega649 ATmega6490 ATmega128 ATmega1280 ATmega1281 ATmega2560 ATmega2561 AT86RF401 AT89S51 AT89S52 AT90PWM2 AT90PWM2B AT90PWM3 AT90PWM3B AT90CAN32 AT90CAN64 AT90CAN128 AT90USB162 AT90USB646 AT90USB647 AT90USB1286 AT90USB1287 *Supports all low voltage versions of the devices with suffix of L/V, such as ATmega16L, ATmega48V Performance - High speed programs FLASH , EEPROM, Fuses, and Lock Bit - It takes only 5.5S to program a 12K program file with verification (AVRISP should be set to high speed 926K mode while the default frequency is 230K) Connects to PC - Uses a quasi-USB interface for communication with the front-end software (Probably AVR Studio) - Using PL2303TA, the USB To RS232 chip - The COM port is configurable, a PC could connects to several USB AVRISP at the same time Connects to target board The USB AVRISP connects to the target board through 3 optional cables. Depending on the existed connector on the target board, the cable has to be changed accordingly. - Standard 10-pin ISP Connector, Using 10-pin ISP cable - Standard 6-pin ISP Connector, Using 10-pin to 6-pin ISP cable - Custom ISP Connector, Using 10-wire multicolour custom connector cable